Frosty's HVAC
4.9 stars · 99 Google reviews

Heating Replacement in Hurst, TX

Three flat-rate residential furnace & heat pump replacement tiers, $8,000-$20,000+. Gas furnace or heat pump configurations. Frosty Thermostat free. Licensed TACLA126718E. Financing with $0 down on approved credit.

Licensed TACLA126718E
EPA 608 Universal Certified
Family-Owned Since 2018
99 Reviews · 4.9 Stars

Where in Hurst Do We Install Furnaces and Heat Pumps?

Our team services Hurst from our Farmers Branch base — 22 miles via SH-183 West, roughly 40 minutes. We cover 76053 and 76054 including Bellaire, Redbud Lane, Pipeline, Mid-Cities Boulevard corridor, and Cottonwood Bend. Hurst sits in Tarrant County.

Now serving Hurst

Hurst is about 40 minutes from our Farmers Branch shop via SH-183 west. Same-day calls are routine when slots open. We carry attic catwalk lumber and replacement attic-handler service platforms because Bellaire and Redbud Lane original installs often need access rebuilt before any coil work starts, plus larger-diameter flex duct so we can quote duct-upsize work alongside any equipment replacement on these capacity-limited 1960s ducting layouts.

Hurst climate and heating context

Hurst's defining repair pattern comes from its original Mid-Hurst housing stock — 1960s split-levels and ranches built when central air was newer and cooling-load assumptions were lower than they are today. Most original Bellaire and Redbud Lane homes were ducted with 6-inch and 7-inch round flex runs to bedrooms; modern equivalent designs use 8-inch and 10-inch trunks for the same square footage because actual cooling demand at 102°F is materially higher than the 1965 design assumption was. Attic-mounted air handlers in those early splits were installed before code required service platforms or even adequate working clearance — a coil-pull on an original Hurst handler can mean rebuilding the catwalk before parts even come off the truck. Capacity-limited ductwork ends up being the silent ceiling on what new equipment can actually deliver in these homes, no matter how high-SEER the new condenser is rated.

How Much Does Heating Replacement Cost in Hurst?

Heating replacement in Hurst runs $8,000-$20,000+ depending on tier, capacity, and whether you choose a gas furnace or a heat pump. All three tiers are flat-rate — the price I quote during the free in-home estimate is the price you pay at install. Financing available with $0 down.

Stay Cool

Goodman · 15 SEER2 · Single-stage

$8,000-$14,000

1-year labor warranty

  • Frosty Thermostat (smart WiFi thermostat)
  • New disconnect box
  • Electrical whip
  • Overflow condensate shutoff
Most Popular

Stay Frosty

Carrier · 18 SEER2 · Dual-stage

$12,000-$18,000

2-year labor warranty

  • Everything in Stay Cool
  • Ductwork inspection + sealing (up to 5 connections)

It's A Frosty Life

Trane · 20+ SEER2 · Variable speed

$16,000-$20,000+

5-year labor warranty

  • Everything in Stay Frosty
  • Full ductwork inspection + sealing
  • Vibration isolation mounts
  • 1-year Frosty Club included ($99 value)

Add-on: 10-Year Labor Warranty +$3,500

Heat pump add-on: +$2,000 over gas furnace in the same tier (combined heating + cooling)

Financing Available

$0 down on approved credit through Optimus, Synchrony, GreenSky. A $12,000 Stay Frosty heating replacement at 9.99% for 120 months runs about $159/month. 50% deposit required at booking.

See Financing Options

What's Included With Every Hurst Heating Replacement?

Every tier — Stay Cool, Stay Frosty, It's A Frosty Life — includes the same baseline package. No bait-and-switch, no surprise add-ons at install. Here's exactly what you get.

Frosty Thermostat (smart WiFi thermostat — our brand, included free)
New electrical whip and disconnect (if needed)
Condensate drain line treatment (90%+ AFUE units)
Combustion analysis after install (gas furnaces)
Copper line inspection (replaced if compromised, for heat pumps)
Load calculation (Manual J)
City permit pulled under TACLA126718E
Full cleanup + haul-away of old equipment
R-454B or R-32 refrigerant (heat pump installs — never R-410A for new)
EPA 608 Universal certified install crew
Post-install walkthrough + WiFi thermostat setup
Manufacturer warranty registration

Why Do Hurst Homeowners Choose Frosty's for Heating Replacement?

Hurst heating replacements are heavily concentrated in the 1960s-80s housing stock — Bellaire, Redbud Lane, Pipeline, and the Mid-Cities Blvd corridor. We're typically pulling out 18-25 year old gas furnaces that have outlived their safe service life and replacing them with single-stage or two-stage 96% AFUE units. For most of these ranch and split-level homes, I recommend a matched system (furnace + AC in the same tier) because mixing a new high-efficiency AC with an old furnace means the new variable-speed blower can't actually modulate properly — and you lose most of the efficiency gain you paid for.

Heat pumps come up a lot in Hurst too, especially in Cottonwood Bend and newer builds. And in Hurst's climate — 20-30 freeze nights, 200+ cooling days — a modern variable-speed heat pump (Trane, Carrier) genuinely makes sense for a lot of homeowners. You get heating and cooling from one system, efficiency down to about 15°F ambient (below that the electric strip heat kicks in), and you drop the annual gas furnace safety inspection because there's no combustion happening. Heat pump adds about $2,000 over the base tier but often qualifies for federal tax credits (ask your tax person) and some Oncor rebates.

Every heating replacement in Hurst includes: new disconnect and electrical whip if needed, proper flue venting or heat pump line set, permit pulled with the city, Frosty Thermostat (our smart WiFi thermostat), condensate management on the new coil, and full cleanup with haul-away of the old equipment. Labor warranty matches the tier: 1-year on Stay Cool, 2-year on Stay Frosty, 5-year on It's A Frosty Life. Financing through Optimus, Synchrony, and GreenSky — $0 down on approved credit.

Neighborhoods we serve in Hurst: Bellaire, Redbud Lane, Pipeline, Mid-Cities Blvd corridor, Cottonwood Bend

Why Should I Trust Frosty's Credentials for Heating Installation?

Because a new furnace install requires a city permit pulled under a licensed contractor — TACLA126718E. Combine that with EPA 608 #2396328 for heat-pump refrigerant work and 99 Google reviews at 4.9 stars, and every credential below is independently verifiable before install day.

TACLA126718E

Texas HVAC Contractor License held by Mariafernanda Jacobo. Every install permitted under this license with the TDLR.

EPA 608 Universal

Omar Jacobo, #2396328. Required by the U.S. EPA for all heat pump installs with R-454B, R-32, and legacy refrigerants under the 2025 phase-down.

DOE Efficiency Partner

All three tiers meet or exceed U.S. Department of Energy AFUE and SEER2 minimums. 90%+ AFUE and 20+ SEER2 tiers qualify for some utility rebates.

Learn more about our credentials on our About page or visit omar-jacobo.com.

Related Services in Hurst

Frosty's covers every residential HVAC need in Hurst, TX — one phone line, one flat-rate pricing book, one licensed (TACLA126718E) family-owned team.

What Do Hurst Homeowners Ask About Heating Replacement?

Should I get a furnace or heat pump in Hurst?

Depends on your existing setup. If you have natural gas already, a 96% AFUE two-stage furnace is typically cheapest to operate through Hurst's 20-30 freeze nights. If you're electric-only or want one system for heating and cooling, a modern variable-speed heat pump works well in Hurst's climate and qualifies for federal tax credits. We quote both numbers so you can compare apples to apples.

How much does heating replacement cost in Hurst, TX?

Full system replacement runs $8,000-$26,000 depending on tier, tonnage, and fuel type. Stay Cool (Goodman 15 SEER2) $8,000-$14,000, Stay Frosty (Carrier 18 SEER2) $12,000-$18,000, It's A Frosty Life (Trane 20+ SEER2) $16,000-$26,000. Heat pump adds $2,000 over the base tier; 10-year labor warranty adds $3,500.

What size furnace do I need for my Hurst home?

Depends on square footage, insulation, window area, and ductwork — not a rule of thumb. We run a Manual J load calculation on every replacement (the ACCA standard). Most 1,200-1,800 sqft 1960s-80s Hurst ranch homes need 60,000-80,000 BTU furnaces. Oversizing is a worse problem than undersizing — it causes short cycling, temperature swings, and humidity issues.

How long does a new furnace or heat pump last in Hurst?

Gas furnaces: 15-20 years with annual maintenance. Heat pumps: 12-15 years because they run year-round for both heating and cooling. Variable-speed equipment typically lasts longer than single-stage because it doesn't cycle on/off as hard. Frosty Club Premium ($300/yr) includes 2 tune-ups per year which extends equipment life significantly.

Do you offer financing for heating replacement in Hurst?

Yes — Optimus, Synchrony, and GreenSky with $0 down on approved credit. 50% deposit at booking, balance on completion. Application takes 5 minutes and most Hurst homeowners get approved same-day. Monthly payments work out to roughly 1/60th of the system price — a $12,000 Stay Frosty install runs about $200/month.

How Do I Get Started with Heating Replacement in Hurst?

Free in-home estimate. Flat-rate pricing. $0 down financing on approved credit. Installation typically within 1-2 weeks.

Written by Omar Jacobo, EPA 608 Universal Certified Lead Technician at Frosty's HVAC LLC. Licensed TACLA126718E. Frosty Club Basic $99/yr · Premium $300/yr.

OJ

Written by

By

Texas Licensed HVAC Contractor #TACLA126718E · EPA #2396328

Co-Owner of Frosty's HVAC LLC, serving DFW since 2018. Learn more

// Ready When You Are

Ready For Reliable HVAC Service?

Request service online, call for same-day help, or see your replacement price.

Call NowBookText Us