Heating Repair in The Colony, TX
Fast, honest, flat-rate residential furnace and heat pump repair in The Colony. Diagnostic $85 (waived with repair). Licensed TACLA126718E, EPA 608 Universal certified, family-owned since 2018.
How Much Does Heating Repair Cost in The Colony?
Furnace repair in The Colonystarts at $85 for the diagnostic (waived with any repair). Most common heating repairs fall in the $250-$1,300 range. We're flat-rate, which means the price quoted before we start is the price you pay at the end. Frosty Club members save 10-15% on every repair.
| Repair | Regular Price | Frosty Club Member |
|---|---|---|
| Diagnostic / service call(Waived with repair) | $85 | $72.25 |
| Furnace ignitor replacement | $400 | $340 |
| Flame sensor replacement | $400 | $340 |
| Pressure switch replacement | $250 – $550 | $212.50 – $467.50 |
| Pilot assembly replacement | $350 – $550 | $297.50 – $467.50 |
| Gas valve replacement | $400 – $1,200 | $340 – $1,020 |
| Inducer motor replacement | $500 – $1,300 | $425 – $1,105 |
| Blower motor (standard) | $750 – $1,500 | $637.50 – $1,275 |
| Blower motor (ECM) | up to $2,800 | up to $2,380 |
| Control board (universal) | $500 | $425 |
| Control board (ECM / modulating) | up to $3,500 | up to $2,975 |
| Thermostat (basic) | $350 | $297.50 |
| Thermostat (programmable) | $500 | $425 |
| Cracked heat exchanger(CO safety — never repaired) | FULL FURNACE REPLACEMENT | FULL FURNACE REPLACEMENT |
Cracked Heat Exchanger: Safety First
A cracked heat exchanger means combustion gases — including carbon monoxide — can leak into your home's air supply. We NEVER repair a cracked heat exchanger. The only safe fix is a full furnace replacement. If I find a crack during diagnostic, I red-tag the unit on the spot and show you our three replacement tiers. Learn more about CO safety at the EPA.
Save More with Frosty Club
Basic ($99/yr):10% off all services | Premium ($300/yr): 15% off + $500 repair credit + 2 free tune-ups (fall heating + spring AC)
Join Frosty ClubWhat Are the Most Common Heating Problems in The Colony?
Texas winters are mild, but furnaces still need regular service — and when they fail on a 28°F January morning, they tend to fail all at once. Here's what I see most often on The Colonyheating calls, and what each one typically costs to fix.
Furnace won't ignite
Failed hot-surface ignitor ($400) or coated flame sensor ($400). Both are same-day fixes. The $85 diagnostic identifies the exact cause.
Blowing cold air instead of hot
Usually a failed ignitor, bad flame sensor, or a stuck gas valve. We run a combustion analysis to confirm the exact cause before quoting.
Loud buzzing or grinding
Dying inducer motor ($500-$1,300) — the draft fan pulling combustion gases through the heat exchanger. Replace before it takes out the control board.
Short cycling (on/off/on/off)
Dirty flame sensor, failing limit switch, or restricted airflow. Can be an early warning of a heat exchanger issue — we diagnose carefully.
Gas smell or CO alarm
EMERGENCY — leave the house, call Atmos Energy at 866-322-8667, then call us. We locate the leak source and repair or red-tag as required.
Cracked heat exchanger
Carbon monoxide risk — NEVER repaired. Full furnace replacement required for safety. We confirm with combustion analyzer and bore-scope inspection.
Why The ColonyHomeowners Trust Frosty's for Heating Repair
North Texas doesn't have Chicago winters, but The Colony still sees 20-30 freeze nights a year, and the humidity off Lewisville Lake turns a 28°F morning into a 28°F morning with ice on everything. That's enough to expose every weak point in a furnace that sat unused from April to October. The calls we get from The Colony in December and January are dominated by three failures: cracked hot-surface ignitors ($400), dirty flame sensors ($400), and stuck or failed gas valves ($400-$1,200). All three have the same symptom — furnace tries to light, fails, goes into lockout. For 1990s Indian Creek homes I also see a lot of aging inducer motors ($500-$1,300) that grind or fail to spin up.
The heat exchanger is the one I worry about most. Crack a heat exchanger and you get carbon monoxide in the supply air — which means we're not repairing it, we're condemning the furnace and quoting a full replacement. Every diagnostic we do in The Colony includes a CO check at the supply register and a visual inspection of the heat exchanger where we can access it. If I see rust, scale, or flame impingement, I tell you straight. I'd rather lose a repair job than let a family breathe CO.
Grandscape and newer Rivers Edge builds often have heat pumps instead of gas furnaces. The winter failures there are different: failed defrost boards, bad reversing valves, and TXV issues on the outdoor unit. Heat pumps run in cooling mode briefly during a defrost cycle to melt ice off the outdoor coil, so if you're seeing steam off the outdoor unit on a cold lake-morning, that's normal — not a problem. Austin Ranch townhomes add one more twist: shared-wall construction means a furnace failure in your unit can actually drop the temperature in your neighbor's unit through the common wall. Call (469) 254-0548 and we'll diagnose whatever's actually wrong for $85 (waived with repair).
Neighborhoods we serve in The Colony: Austin Ranch, Grandscape, Rivers Edge, Indian Creek, Stewart Peninsula
Why Our Credentials Matter for Heating Repair
TACLA126718E
Texas HVAC Contractor License held by Mariafernanda Jacobo. Issued and regulated by the Texas Department of Licensing and Regulation.
EPA 608 Universal
Omar Jacobo, #2396328. Required by the U.S. EPA for any refrigerant work on heat pumps (R-22, R-410A, R-454B, R-32). Also ensures safe combustion analysis standards.
Energy Star Partner
Replacement heating systems meet or exceed U.S. Department of Energy minimums. 90%+ AFUE furnaces and ENERGY STAR heat pumps qualify for some utility rebates.
Learn more about our credentials on our About page or visit omar-jacobo.com.
Heating Repair FAQ for The Colony, TX
How much does furnace repair cost in The Colony, TX?
Diagnostic $85 flat (waived with repair). Common The Colony furnace repairs: hot-surface ignitor $400 ($340 for Frosty Club members), flame sensor $400 ($340), gas valve $400-$1,200 ($340-$1,020), inducer motor $500-$1,300 ($425-$1,105), pressure switch $250-$550. We're flat-rate, so you see the total before we start.
Is my furnace safe to run if the heat exchanger is cracked?
No. A cracked heat exchanger leaks combustion gases — including carbon monoxide — directly into your supply air. We don't repair cracked heat exchangers because they can't be safely welded back to spec. Instead, we quote a full furnace replacement. Every The Colony diagnostic includes a heat exchanger inspection and CO check at the supply register.
Do you repair heat pumps in The Colony?
Yes. Grandscape and newer Rivers Edge homes often have heat pumps instead of gas furnaces. Common heat pump failures include defrost board faults, failed reversing valves, and outdoor TXV issues. We service Carrier, Trane, Goodman, Lennox, Rheem, and all major residential brands.
Why does my The Colony furnace keep shutting off after a few minutes?
Short cycling on a furnace is usually a dirty flame sensor (most common), overheating due to restricted airflow (clogged filter or dirty blower), or a failing pressure switch. The $85 diagnostic identifies the cause. Flame sensor cleaning runs $400 flat ($340 for members) and solves 60% of these calls.
My Austin Ranch townhome is cold even though the furnace runs — why?
In shared-wall Austin Ranch townhomes, a furnace that runs but doesn't warm the unit usually means under-speed blower (failing ECM motor), a zoning damper stuck closed on the upstairs, or a supply plenum leaking into the mechanical closet instead of the duct system. Tight closets hide leaks. Our $85 diagnostic finds it and we quote flat-rate.
Related Services & Resources
Need Heating Repair in The Colony Right Now?
Call us or request service online. Same-day appointments available for The Colony homeowners during winter cold snaps. Flat-rate pricing — no surprises, no hourly charges, no upsell scripts.
Written by Omar Jacobo, EPA 608 Universal Certified Lead Technician at Frosty's HVAC LLC. Licensed TACLA126718E.
Written by
Omar Jacobo
EPA 608 Certified Technician (#2396328) | Co-Owner, Frosty's HVAC LLC
Omar has been serving local homeowners since 2018. Learn more
Ready For Reliable HVAC Service?
Request service online, call for same-day help, or see your replacement price.
Call Now