Fast, honest, flat-rate residential furnace and heat pump repair in Coppell. Diagnostic $85 (waived with repair). Licensed TACLA126718E, EPA 608 Universal certified, family-owned since 2018.
Real stories from recent Frosty's HVAC jobs in Coppell, TX -- published straight from the field.
When a family on South MacArthur Blvd in Coppell called because their system wouldn't cool, our technician traced the problem to an electrical wiring issue related to a recent breaker replacement. After correcting the wiring, the system began operating properly, but further testi...
Our team services Coppell from our Farmers Branch base — 7 miles via I-635 West to MacArthur Boulevard, roughly 12 minutes. We cover 75019 and 75099 including Riverchase, Cypress Waters, Northlake Woodlands, Old Coppell, and MacArthur Corridor. Coppell sits in Dallas County.
Coppell is 10-12 minutes from our Farmers Branch shop via I-635 west to MacArthur. Same-day response is routine across 75019 from Riverchase to Old Coppell. We stock float switches and condensate drain treatment for the lake-humidity coil-clog problem, plus dual-zone capacitors and contactors for the 1990s-2000s two-story housing in Northlake Woodlands and Copperstone where upstairs units fail first.
Coppell sits next to Grapevine Lake, and every April through June cottonwood drift packs onto outdoor condenser fins like felt — choking airflow, overheating compressors, and pre-aging capacitors. Lake humidity also accelerates condensate-line algae growth in attic-mounted air handlers, which is why two-story Riverchase and Northlake Woodlands homes see drain-pan overflow events earlier in the season than dry inland cities.
Furnace repair in Coppell starts at $85 for the diagnostic (waived with any repair). Most common heating repairs fall in the $250-$1,300 range. We're flat-rate, which means the price quoted before we start is the price you pay at the end. Frosty Club members save 10-15% on every repair.
| Repair | Regular Price | Frosty Club Member |
|---|---|---|
| Diagnostic / service call(Waived with repair) | $85 | $0 — never for members |
| Furnace ignitor replacement | $400 | $340 |
| Flame sensor replacement | $400 | $340 |
| Pressure switch replacement | $250 – $550 | $212.50 – $467.50 |
| Pilot assembly replacement | $350 – $550 | $297.50 – $467.50 |
| Gas valve replacement | $400 – $1,200 | $340 – $1,020 |
| Inducer motor replacement | $500 – $1,300 | $425 – $1,105 |
| Blower motor (standard) | $750 – $1,500 | $637.50 – $1,275 |
| Blower motor (ECM) | up to $2,800 | up to $2,380 |
| Control board (universal) | $500 | $425 |
| Control board (ECM / modulating) | up to $3,500 | up to $2,975 |
| Thermostat (basic) | $350 | $297.50 |
| Thermostat (programmable) | $500 | $425 |
| Cracked heat exchanger(CO safety — never repaired) | FULL FURNACE REPLACEMENT | FULL FURNACE REPLACEMENT |
A cracked heat exchanger means combustion gases — including carbon monoxide — can leak into your home's air supply. We NEVER repair a cracked heat exchanger. The only safe fix is a full furnace replacement. If I find a crack during diagnostic, I red-tag the unit on the spot and show you our three replacement tiers. Learn more about CO safety at the EPA.
Basic ($99/yr):10% off all services | Premium ($300/yr): 15% off + $500 repair credit + 2 free tune-ups (fall heating + spring AC)
Join Frosty ClubTexas winters are mild, but furnaces still need regular service — and when they fail on a 28°F January morning, they tend to fail all at once. Here's what I see most often on Coppellheating calls, and what each one typically costs to fix.
Failed hot-surface ignitor ($400) or coated flame sensor ($400). Both are same-day fixes. The $85 diagnostic identifies the exact cause.
Usually a failed ignitor, bad flame sensor, or a stuck gas valve. We run a combustion analysis to confirm the exact cause before quoting.
Dying inducer motor ($500-$1,300) — the draft fan pulling combustion gases through the heat exchanger. Replace before it takes out the control board.
Dirty flame sensor, failing limit switch, or restricted airflow. Can be an early warning of a heat exchanger issue — we diagnose carefully.
EMERGENCY — leave the house, call Atmos Energy at 866-322-8667, then call us. We locate the leak source and repair or red-tag as required.
Carbon monoxide risk — NEVER repaired. Full furnace replacement required for safety. We confirm with combustion analyzer and bore-scope inspection.
I'm Omar Jacobo, owner of Frosty's HVAC. Coppell heating calls peak December through February when North Texas drops below freezing for 20-30 nights. The dominant Coppell housing — 1990s-2000s two-story homes in Riverchase, Northlake Woodlands, Alexander Court, and Copperstone — runs 80% AFUE gas furnaces fueled by Atmos Energy natural gas, installed in attic closets or dedicated second-floor utility closets. These builder-grade furnaces are now 25+ years old, and the failure patterns are textbook age-related: hot-surface ignitors ($400, $340 for members) cracking after thousands of heat cycles, flame sensors ($400, $340) fouled with carbon deposits, pressure switches ($250-$550) stuck from summer attic dust, inducer motors ($500-$1,300) wearing out bearings, and gas valves ($400-$1,200) failing on original Honeywell controls.
The Coppell-specific wrinkle is the proximity to Grapevine Lake. Lake humidity during fall and early winter accelerates corrosion on the heat exchanger — the critical component that separates combustion gases from your breathable air. On a 20+ year old Coppell furnace, a cracked heat exchanger leaks carbon monoxide directly into the supply air that circulates through every bedroom of a two-story home. I take this seriously: every furnace diagnostic on a 15+ year old Coppell system includes a CO check at a supply register and a visual heat exchanger inspection. We don't repair cracked heat exchangers — they cannot be safely welded back to factory spec. If the exchanger is compromised, we condemn the furnace and quote full replacement. All Coppell gas furnace work follows NFPA 54 standards and Atmos Energy connection requirements.
Old Coppell — the pre-1990 ranch homes on crawlspaces along Coppell Road and Bethel Road — runs a mix of older 80% AFUE units and some early 90% AFUE condensing furnaces with problematic secondary heat exchangers. These condensing units produce acidic condensate that corrodes the secondary exchanger from the inside out, so a 20-year-old condensing furnace in Old Coppell often needs replacement rather than repair. Diagnostic is $85 flat (waived with any repair). I'm EPA 608 Universal certified (#2396328), Mariafernanda holds TACLA126718E, and we carry 143 Google reviews at 4.9 stars. Call (469) 254-0548 — a human answers.
Neighborhoods we serve in Coppell: Riverchase, Cypress Waters, Northlake Woodlands, Old Coppell, MacArthur Corridor
Because a gas furnace that's repaired wrong can leak carbon monoxide. Every credential below — TACLA126718E, EPA 608 #2396328, 143 Google reviews — is independently verifiable. We red-tag cracked heat exchangers on the spot; we never patch them.
Texas HVAC Contractor License held by Mariafernanda Jacobo. Issued and regulated by the Texas Department of Licensing and Regulation.
Omar Jacobo, #2396328. Required by the U.S. EPA for any refrigerant work on heat pumps (R-22, R-410A, R-454B, R-32). Also ensures safe combustion analysis standards.
Replacement heating systems meet or exceed U.S. Department of Energy minimums. 90%+ AFUE furnaces and ENERGY STAR heat pumps qualify for some utility rebates.
Learn more about our credentials on our About page or visit omar-jacobo.com.
Frosty's covers every residential HVAC need in Coppell, TX — one phone line, one flat-rate pricing book, one licensed (TACLA126718E) family-owned team.
Same flat-rate heating repairpricing across every city we cover. If you're in a Coppell-adjacent neighborhood, these pages have local details for your ZIP.
Deeper context on heating repair written by Omar Jacobo (EPA 608 #2396328).
Diagnostic $85 flat (waived with repair). Common Coppell furnace repairs: ignitor $400 ($340 for Frosty Club members), flame sensor $400 ($340), pressure switch $250-$550, inducer motor $500-$1,300 ($425-$1,105), gas valve $400-$1,200. All flat-rate — you see the total before we start. Frosty Club Premium members save 15% on every repair plus get a $500 credit.
Possibly not. A 20+ year old furnace in Coppell — especially in the humid neighborhoods near Grapevine Lake like Riverchase and MacArthur Corridor — has elevated risk of heat exchanger cracks that leak carbon monoxide into your home's air supply. Every diagnostic I run on a 15+ year old system includes a CO check and visual heat exchanger inspection. If the exchanger is cracked, we condemn it. Carbon monoxide is odorless and colorless — you won't know until a detector goes off or someone gets sick.
Hot-surface ignitors are consumable parts — they crack from thermal cycling after 8-15 years of daily use during heating season. In Coppell's two-story homes where the furnace sits in a dusty attic space, ignitors can fail sooner because dust accumulates on the element and creates hot spots. Replacement is $400 flat ($340 for Frosty Club members). We stock universal ignitors on the truck for same-day Coppell repairs.
Yes — Carrier, Trane, Goodman, Lennox, Rheem, York, Amana, Bryant, Payne, and all other residential brands. Most Coppell homes in Riverchase and Northlake Woodlands shipped with builder-grade Goodman or Carrier units. Regardless of brand, parts like ignitors, flame sensors, pressure switches, and gas valves are all serviceable. Diagnostic is $85 flat (waived with repair).
Short cycling followed by lockout usually means a dirty flame sensor ($400 flat), a failing pressure switch ($250-$550), or restricted airflow from a clogged filter forcing the limit switch to trip. On Coppell 90%+ AFUE condensing furnaces in Old Coppell, a clogged condensate drain can also trigger a pressure switch lockout. The $85 diagnostic identifies the exact cause. Frosty Club members get priority scheduling during freeze events when Coppell furnace calls spike.
Yes — EPA 608 Universal cert #2396328 lets me legally recover, recycle, and recharge R-22 under federal regulations. R-22 production ended in 2020 under the Clean Air Act phase-out (EPA.gov), so it now runs $200 per pound installed. A typical Riverchase and Cypress Waters R-22 leak repair totals $650-$1,000: electronic leak detection ($250) or nitrogen leak test ($500) plus recharge at $200/lb. Optional leak seal $350 — but it can void manufacturer warranties, so I only recommend it in specific cases. For systems past 12 years with major leaks, planning the transition to R-454B or R-32 is usually the better economics. Read our R-410A phase-out explainer for DFW homeowners.
Yes — heat pumps and ACs use the same refrigerant rules. EPA 608 Universal cert #2396328 covers R-410A heat pump service. AIM Act 2025 phase-out (Energy.gov) only stops new equipment manufacture — existing Riverchase and Cypress Waters heat pumps stay serviceable. Repair cost runs the same as AC: $250-$500 for leak detection plus $100/lb recharge. Repair is usually right unless the system is past 12 years old. Read our R-410A phase-out explainer for DFW homeowners.
Call us or request service online. Same-day appointments available for Coppell homeowners during winter cold snaps. Flat-rate pricing — no surprises, no hourly charges, no upsell scripts.
Written by Omar Jacobo, EPA 608 Universal Certified Lead Technician at Frosty's HVAC LLC. Licensed TACLA126718E.
Written by
By Omar Jacobo
Texas Licensed HVAC Contractor #TACLA126718E · EPA #2396328
Co-Owner of Frosty's HVAC LLC, serving DFW since 2018. Learn more
Request service online, call for same-day help, or see your replacement price.
Call Now