Frosty's HVAC
troubleshooting8 min read

Pilot Light Won't Stay Lit? 5 Common Causes and Fixes

By Omar Jacobo, Licensed HVAC Technician (EPA 608 #2396328)

The pilot light call is one of the oldest troubleshooting calls I take. Modern electronic ignition has replaced the standing pilot in almost every furnace built after the early 2000s, but I still service dozens of older systems every fall in Farmers Branch ranch homes, South Irving bungalows, and small Grapevine houses built in the 1970s-80s. When that pilot won't stay lit, it's almost always one of five things. Here's how to diagnose it.

I'm Omar Jacobo, EPA 608 Universal Certified and co-owner of Frosty's HVAC (TACLA126718E). I service every generation of residential gas furnace — from 1970s standing pilots to today's modulating condensing systems. Let's troubleshoot.

What Is a Pilot Light and How Does It Work?

A pilot light is a small continuous flame that burns at the base of the main burner assembly in older gas furnaces. Its job is to ignite the main burner when the thermostat calls for heat. A thermocouple sits in the pilot flame and generates a tiny electrical current (millivolts) that keeps the gas valve open — if the pilot goes out, the thermocouple cools, voltage drops, and the gas valve shuts to prevent gas from leaking into your home.

It's a beautifully simple system, actually. The pilot is its own safety switch. No pilot flame, no gas to the main burner. The catch: if the thermocouple is weak or the pilot is unstable, you get the problem this post is about — pilot won't stay lit.

Important: if your furnace has a hot surface ignitor (a small ceramic rod that glows orange) or a spark ignitor, it does not have a pilot light. This post is for standing-pilot furnaces only, which are typically 25+ years old.

Related: Why Your Furnace Keeps Turning On and Off (Short Cycling).

What Are the 5 Most Common Causes of a Pilot That Won't Stay Lit?

1. Dirty or Failed Thermocouple (Most Common)

A weak thermocouple is the #1 cause of pilot light failures I see in the field. The thermocouple tip sits in the pilot flame and generates voltage from heat. Over years, carbon builds up on the tip, the metal oxidizes, and the voltage output drops below what the gas valve needs to stay open.

Symptoms:

  • Pilot lights fine but won't stay lit after you release the reset button
  • Pilot stays lit for 30-60 seconds then goes out
  • Getting harder and harder to light each time

The fix: Replace the thermocouple. It's a $20 part and a 20-30 minute job for me.

Cost: $350-$450 (Member: $297.50-$382.50). I realize the markup seems high on a $20 part, but the repair includes the trip, diagnosis, pulling the burner assembly on some furnace models, and testing the rest of the system to make sure nothing else is contributing.

2. Dirty Pilot Orifice

A clogged pilot orifice means the small flame can't get enough gas to burn stable. The flame flickers, burns yellow, or won't stay lit at all. Dust, lint, and spider webs (yes, really — spiders love warm gas pipes) are the usual culprits.

Symptoms:

  • Yellow or flickering pilot flame instead of blue
  • Pilot goes out when there's any draft
  • Intermittent ignition problems

The fix: Clean the orifice with compressed air and a soft brush. Never use a pin or wire — you'll enlarge the orifice and cause other problems.

Cost: Usually bundled into a $150 tune-up (Member: $127.50) or a $350 cleaning service call.

3. Drafty Mechanical Closet or Attic

Older furnaces in drafty spaces can have their pilot blown out by wind gusts, especially if the combustion chamber door is loose or there's a gap in the flue pipe. Farmers Branch and Irving attics take heavy wind during fall cold fronts, and the pilot flame is tiny.

Symptoms:

  • Pilot goes out during windy days
  • Problem gets worse when cold fronts move through
  • Pilot stays lit in calm weather

The fix: Seal the mechanical closet door, inspect flue pipe joints, and address any attic air leakage. On a furnace this old, I also recommend evaluating the entire system for replacement because drafty installations often have other age-related issues.

Cost: $150-$400 depending on seal-up scope.

4. Clogged or Partially Blocked Flue

A furnace flue that's partially blocked by nests, debris, or a collapsed joint creates backdraft conditions that can blow out the pilot — and in the worst case, push combustion gases (including carbon monoxide) back into your home.

Symptoms:

  • Pilot goes out and you smell exhaust gases
  • Soot marks around the flue draft hood
  • CO detector alarms briefly when the furnace runs

The fix: Inspect and clean the flue. If the flue is damaged, it must be repaired or replaced to continue safe operation. This is not optional — a blocked flue is a carbon monoxide emergency waiting to happen.

Cost: $350-$900 depending on repair scope.

5. Failing Gas Valve

The gas valve is what lets gas flow to the pilot and main burner. When the internal solenoid weakens, it doesn't hold the pilot open reliably even with a good thermocouple signal.

Symptoms:

  • Pilot lights but shuts off randomly, not consistently
  • Other combustion problems accompanying the pilot issue
  • Gas smells around the valve body

The fix: Replace the gas valve. This is more invasive than a thermocouple swap.

Cost: $500-$800 (Member: $425-$680).

How Do I Relight a Pilot Light Safely?

You can relight most pilot lights yourself in about 2 minutes using the instruction sticker on the furnace. Here's the standard procedure, but always read the sticker on your specific unit first:

  1. Turn the gas control knob to OFF. Wait 5 minutes with the closet door open to let any accumulated gas dissipate.
  2. Smell for gas. If you smell gas strongly, STOP. Ventilate the area, shut off gas at the meter if you know how, leave the home, and call 911 or us at (469) 254-0548 from outside.
  3. Turn the knob to PILOT. Press and hold the reset button.
  4. Light the pilot with a long lighter or long match while holding the reset button down.
  5. Hold the reset button 30-60 seconds after the pilot lights. This lets the thermocouple heat up and signal the gas valve to stay open.
  6. Release the reset button. The pilot should stay lit.
  7. Turn the knob to ON. Set your thermostat to heat and confirm the main burner ignites normally.

If the pilot goes out within seconds of releasing the reset button, you have a thermocouple or gas valve problem — call me.

Safety rule: Never relight a pilot if you smell gas. The consequences of a gas leak ignition are severe. Get out and call for help.

Related: 5 Signs Your Furnace Needs Repair (Before Winter Hits).

Is It Time to Replace an Old Furnace With a Pilot Light?

If your furnace uses a standing pilot light, it's almost certainly 25+ years old, and replacement deserves serious consideration. These older systems run at 60-65% AFUE efficiency, meaning 35-40% of your gas bill is wasted heat going out the flue. Modern high-efficiency furnaces hit 95%+ AFUE, which translates to real money saved every month.

When I walk homeowners through the replace-vs-repair decision on an old standing-pilot system:

Replace if:

  • The furnace is 25+ years old (most standing pilots are)
  • The next repair is $800+
  • Energy bills are climbing year over year
  • You're planning to stay in the home 5+ years
  • The heat exchanger has any visible corrosion or rust

Repair if:

  • The repair is $350-$500 (a thermocouple or similar)
  • You're planning to move within 1-2 years
  • The system is otherwise sound

A full HVAC system replacement in DFW is $8,000 to $20,000+ depending on tier. Use our AC Replacement Cost Calculator for exact pricing on your home.

The Department of Energy estimates that upgrading from a 65% AFUE furnace to a 95% AFUE unit saves homeowners roughly 30 cents of every dollar spent on heating. On a $200/month winter gas bill, that's $60/month — $300-$400 per heating season in DFW. The replacement pays back through bill savings and eliminates the risk of a decades-old heat exchanger developing cracks.

Schedule a Pilot Light Diagnosis

If your pilot light won't stay lit, I can diagnose the cause and quote flat-rate repair on the first visit. Bring a phone picture of the stickers on your furnace if you have one — it helps me confirm the model before the call so I can bring the right parts.

Call (469) 254-0548 or request service online.

Serving Farmers Branch, Coppell, Irving, Flower Mound, Lewisville, and Grapevine.

Considering replacement? See real pricing. Save on every service — join Frosty Club. Meet the family behind Frosty's.

Related Articles


Written by Omar Jacobo, EPA 608 Universal Certified Lead Technician at Frosty's HVAC LLC. Family-owned since 2018, 143 Google reviews at 4.9 stars, Texas License TACLA126718E. Serving DFW homeowners with flat-rate pricing and no surprises.

Frequently Asked Questions

Why does my pilot light keep going out?

The most common reason a pilot light keeps going out is a failed or dirty thermocouple, which costs $350-$450 (Member: $297.50-$382.50) to replace. Other common causes include a dirty pilot orifice, drafty mechanical closet, clogged flue, or a weakening gas valve. Older standing-pilot furnaces are the ones that use pilot lights — newer furnaces use electronic ignition.

How old is my furnace if it has a pilot light?

If your furnace has a standing pilot light, it's typically 25+ years old. Electronic ignition replaced standing pilots in residential furnaces during the late 1990s and early 2000s. A furnace that old should be evaluated for replacement during the next repair call — efficiency is 30-40% lower than modern units, and parts are getting harder to source.

Can I light the pilot light myself?

Yes, most standing-pilot furnaces have a clear 'Light Pilot' instruction sticker on the unit. You turn the gas control to Pilot, press and hold the reset button, light the pilot with a long lighter, and keep holding for 30-60 seconds until the thermocouple heats up. If you smell gas before lighting, STOP — ventilate the area, shut off the gas, and call (469) 254-0548 or 911 if strong.

Is a pilot light dangerous?

A properly working pilot light is not dangerous — it's a small controlled flame that burns a tiny amount of gas continuously. It becomes dangerous only when something goes wrong: gas leaks, improper combustion, or a cracked heat exchanger. If you smell gas, see soot around the pilot area, or have a CO detector alarm, shut the system off and call us immediately.

Should I replace an old furnace with a pilot light?

Yes, especially if it's 25+ years old and needs any significant repair. Standing-pilot furnaces run at 60-65% AFUE efficiency, while modern high-efficiency furnaces hit 95%+ AFUE. Full HVAC system replacement ($8,000-$20,000+) typically pays back through energy savings and eliminates the risk of a decades-old heat exchanger developing cracks.

OJ

Written by

By

Texas Licensed HVAC Contractor #TACLA126718E · EPA #2396328

Co-Owner of Frosty's HVAC LLC, serving DFW since 2018. Learn more

// Ready When You Are

Ready For Reliable HVAC Service?

Request service online, call for same-day help, or see your replacement price.

Call NowBookText Us